Estimates on the power I'm making?? - Chevy and GMC Duramax Diesel Forum
Competition Discuss Drag Racing, Sled Pulling, and Dyno Event setup, technique, and results.

 3Likes
Reply
 
LinkBack Thread Tools Display Modes
post #1 of 15 (permalink) Old 05-03-2019, 06:07 AM Thread Starter
DuramaxForum n00b
 
CowboyElvis's Avatar
 
Join Date: Sep 2018
Posts: 20
Estimates on the power I'm making??

Ok, so I bought this truck recently, lot of work went into it, but it was never dynoed. Here's the list
ARP studs
Engine breather kit
20% injectors
83mm borgwarner turbo
4" down into 5" exhaust
5" SDP intake
100hp tune
CP3 fuel pump
FASS 150 fuel system
Sun coast stage 3 transmission

no idea what the power would be and nearest dyno to me is over 2 hours away. Just curious if maybe you comp guys might have a better idea?
CowboyElvis is offline  
Sponsored Links
Advertisement
 
post #2 of 15 (permalink) Old 05-03-2019, 06:17 AM
DuramaxForum Fanatic
 
SilverGorillaLML's Avatar
 
Join Date: Feb 2015
Location: The mountains of va/wva listen for the banjos
Posts: 9,453
83mm in a compound or single? I'd say mid to high 500s. Maybe maybe maybe maybe low 6s. Take it to the track run it and then plug that in to the calculator on competition diesels site or dd

2012 QCSB/Built 6.8L Cummins/48RE/Gated shifter
SilverGorillaLML is online now  
post #3 of 15 (permalink) Old 05-03-2019, 06:19 AM
DuramaxForum Guru
 
1TRIKHD's Avatar
 
Join Date: Jul 2012
Location: Where Loggers do it better in the Woods. PNW Son!
Posts: 17,258
Quote:
Originally Posted by CowboyElvis View Post
Ok, so I bought this truck recently, lot of work went into it, but it was never dynoed. Here's the list
ARP studs
Engine breather kit
20% injectors
83mm borgwarner turbo
4" down into 5" exhaust
5" SDP intake
100hp tune
CP3 fuel pump
FASS 150 fuel system
Sun coast stage 3 transmission

no idea what the power would be and nearest dyno to me is over 2 hours away. Just curious if maybe you comp guys might have a better idea?
Can you be more spexific on the specs of the turbo. Stock cp3? New? Who's injectors?

Sent from my VS988 using Tapatalk

2006 Victory Red CCLB LT3 LBZ
Tuned by Blake Crenshaw
SDP Fully Built Trans w/ Billet Goerend G Converter
S472 SX-E.87/1.0ar sitting on a Wagler street intake W/ a twisted pedestal
Stock Sticks
Special thanks to Scott with Screaming Diesel Performance
Blake with Unleashed Duramax tuning
1TRIKHD is online now  
Sponsored Links
Advertisement
 
post #4 of 15 (permalink) Old 05-03-2019, 06:20 AM Thread Starter
DuramaxForum n00b
 
CowboyElvis's Avatar
 
Join Date: Sep 2018
Posts: 20
It is a single turbo, forgot to mention that, so there is a bit of lag getting her going...but I'm never going to own a gas truck ever again after this
CowboyElvis is offline  
post #5 of 15 (permalink) Old 05-03-2019, 06:22 AM
DuramaxForum Guru
 
1TRIKHD's Avatar
 
Join Date: Jul 2012
Location: Where Loggers do it better in the Woods. PNW Son!
Posts: 17,258
Quote:
Originally Posted by SilverGorillaLML View Post
83mm in a compound or single? I'd say mid to high 500s. Maybe maybe maybe maybe low 6s. Take it to the track run it and then plug that in to the calculator on competition diesels site or dd
I was going to say 500's as well but need more info.

Sent from my VS988 using Tapatalk

2006 Victory Red CCLB LT3 LBZ
Tuned by Blake Crenshaw
SDP Fully Built Trans w/ Billet Goerend G Converter
S472 SX-E.87/1.0ar sitting on a Wagler street intake W/ a twisted pedestal
Stock Sticks
Special thanks to Scott with Screaming Diesel Performance
Blake with Unleashed Duramax tuning
1TRIKHD is online now  
post #6 of 15 (permalink) Old 05-03-2019, 06:56 AM
DuramaxForum Fanatic
 
SilverGorillaLML's Avatar
 
Join Date: Feb 2015
Location: The mountains of va/wva listen for the banjos
Posts: 9,453
Yes I love big singles! Haha. Need to throw more fuel at that thing. I'd go at least 60 or 100 and leave the stock cp3 as your limiter for now depending on what year motor you have pistons or rods will be the thing to worry about. Stock cp3 should do low to mid 600s. What converter do you have and what's the specs on the charger? Whose doing the tuning? I would have them change the shift points for the transmission, and the speed the converter locks up at when cruising so it's easier to stay ontop the charger.

2012 QCSB/Built 6.8L Cummins/48RE/Gated shifter
SilverGorillaLML is online now  
post #7 of 15 (permalink) Old 05-03-2019, 09:55 AM
DuramaxForum Guru
 
1TRIKHD's Avatar
 
Join Date: Jul 2012
Location: Where Loggers do it better in the Woods. PNW Son!
Posts: 17,258
Quote:
Originally Posted by SilverGorillaLML View Post
Yes I love big singles! Haha. Need to throw more fuel at that thing. I'd go at least 60 or 100 and leave the stock cp3 as your limiter for now depending on what year motor you have pistons or rods will be the thing to worry about. Stock cp3 should do low to mid 600s. What converter do you have and what's the specs on the charger? Whose doing the tuning? I would have them change the shift points for the transmission, and the speed the converter locks up at when cruising so it's easier to stay ontop the charger.
I agree, I had blake bump up the rpm to hell stay on top of my 72mm and its not that laggy at all.. 100 overs are like 60's now Nic. Lol. Do 150s at least.

Sent from my VS988 using Tapatalk

2006 Victory Red CCLB LT3 LBZ
Tuned by Blake Crenshaw
SDP Fully Built Trans w/ Billet Goerend G Converter
S472 SX-E.87/1.0ar sitting on a Wagler street intake W/ a twisted pedestal
Stock Sticks
Special thanks to Scott with Screaming Diesel Performance
Blake with Unleashed Duramax tuning
1TRIKHD is online now  
post #8 of 15 (permalink) Old 05-03-2019, 10:06 AM
DuramaxForum Fanatic
 
SilverGorillaLML's Avatar
 
Join Date: Feb 2015
Location: The mountains of va/wva listen for the banjos
Posts: 9,453
100 overs will still do 9 to 1k depending on cp3s lol. Some of yall are getting injector happy lol. That 83 would love some 200s though and dual pumps. Rods and pistons wont theough lol
1TRIKHD likes this.

2012 QCSB/Built 6.8L Cummins/48RE/Gated shifter
SilverGorillaLML is online now  
post #9 of 15 (permalink) Old 05-03-2019, 10:46 AM
DuramaxForum Guru
 
1TRIKHD's Avatar
 
Join Date: Jul 2012
Location: Where Loggers do it better in the Woods. PNW Son!
Posts: 17,258
Quote:
Originally Posted by SilverGorillaLML View Post
100 overs will still do 9 to 1k depending on cp3s lol. Some of yall are getting injector happy lol. That 83 would love some 200s though and dual pumps. Rods and pistons wont theough lol
Yeah your right Nic, just seeing how much money I can get him to spend Lmao.

Sent from my VS988 using Tapatalk

2006 Victory Red CCLB LT3 LBZ
Tuned by Blake Crenshaw
SDP Fully Built Trans w/ Billet Goerend G Converter
S472 SX-E.87/1.0ar sitting on a Wagler street intake W/ a twisted pedestal
Stock Sticks
Special thanks to Scott with Screaming Diesel Performance
Blake with Unleashed Duramax tuning
1TRIKHD is online now  
post #10 of 15 (permalink) Old 05-03-2019, 11:23 AM
DuramaxForum Fanatic
 
SilverGorillaLML's Avatar
 
Join Date: Feb 2015
Location: The mountains of va/wva listen for the banjos
Posts: 9,453
Oh well if were doing that then it needs every part wagler or SoCal can fit in the fed ex truck
Noble_dmax and 1TRIKHD like this.

2012 QCSB/Built 6.8L Cummins/48RE/Gated shifter
SilverGorillaLML is online now  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Chevy and GMC Duramax Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
Brake and power steering making pyulsing noises!! bluearc74 Drivetrain 16 07-24-2013 05:34 PM
03 LB7, Edge Juice w/ Attitude not making any extra power? Andrew03Dmax 01-04.5 LB7 Performance Parts Discussion 1 10-16-2012 08:07 PM
making power lovemesomebowtie Performance Upgrades 3 08-12-2009 06:07 AM
epa estimates for lmm duramax duramax2be 2007.5 + (GMT 900) Non Powertrain--New Body Style-- 6 08-06-2008 05:20 AM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome